Who owns Briggs bathtubs?
In late 2011, Briggs was acquired by senior management. Briggs® Plumbing Products is now totally an American-owned company with a renewed focus on business expansion, new products and supply chain enhancements with manufacturing operations on three continents.
What does AFR mean in bathtubs?
Above-the-Floor Rough
Above-the-Floor Rough (AFR) for bathtubs. The unique Above-the-Floor Rough (AFR) feature for bathtubs leaves a few inches of clearance between the product’s underside and the flooring so pipes can be routed without breaking ground or relocating the drain.
What are standard tub sizes?
Standard tubs usually have external measurements around 60 inches long, 30 inches wide and 14 to 16 inches high. When shopping for a soaking tub, find a tub that measures between 60 inches long and 72 inches long. Persons over six feet tall may want to consider an oversized bathtub for the most comfort.
What is the standard size of an old cast iron tub?
The most common sizes for cast iron bathtubs would be 66 inches and 72 inches. Of course if you want something smaller, they can go down to 60 inches if you have a smaller space. The reason for the popularity of these sizes is due to their incredible versatility.
Where are Briggs tubs made?
Briggs has executive offices at its manufacturing facilities in Knoxville. Distribution and administrative activities will remain at the company’s Charleston, SC complex.
What does deep sump height mean?
Technically, Deep Sump Height is the measurement from the bottom of tub (at drain) to the bottom of overflow. So practically speaking, Deep Sump Height is the same as its soaking depth.
How high should a tub drain be from the floor?
Discharge hole (vertical): About 16 to 20 inches above the floor; consider drain pipe to be the vertical centerline. Fixture (side to side buffer): From centerline, 15 inches minimum, 20 inches recommended.
How are tubs measured?
The basin length should be measured at its widest point in the middle of the tub, from left to right. The length always refers to the longest point of the tub. To find the basin width, measure from the midpoint of the length of the tub, front to back.
What is a good soaking depth for a tub?
14”
Standard tub depths allow for approximately 12” of water; soaking tubs should offer at least 14” or more so that the water covers the majority of the bather’s body. To determine water depth, measure the tub from the bottom (interior) to the overflow drain.
Are old bathtubs worth money?
Yes, you can sell your old bathtub. On average, a reused or salvaged bathtub will run anywhere from $300-$1,000, depending on the material and quality of the bathtub.
Are cast iron tubs better than acrylic?
Cast iron tubs are extremely durable and require less upkeep than an acrylic tub to keep them in good shape. They should be cleaned weekly using a mixture of soap and water and a soft sponge or cloth. Acrylic tubs are very durable, but more prone to staining over time.
Can a sump pump be too deep?
If your sump pit reaches deep below the floor, then it’s gathering much more water than it needs to – and it’s forcing your pump to work longer and harder to pump water out. This will unnecessarily shorten the life of your system, increase the likelihood of overheating, and cost you extra on your electric bill.
How far can P-trap be from tub drain?
Plumbing Codes P-Traps must connect to the same size drain outlet, with a diameter of at least 1.5 inches. The vertical distance from the fixture to the trap can not exceed 24 inches. The horizontal distance from the fixture to the trap should not exceed 30 inches.
Can I replace a 30 inch tub with 32?
The bigger issue is when the width of the new tub exceeds the old space. Replacing a 30-inch tub with a 32-inch tub is an example. If the floor is concrete, this makes adjusting the flooring more difficult. Tile, vinyl, and wood gets brittle with age.