How do I reset my Grandstream HT502?

By Other

How do I reset my Grandstream HT502?

Hold the recessed reset button down using something that is solid but small in diameter like a paperclip or push pin. Continue holding the button down. While holding the button down please note the lights on the front of the device. After approximately 8 seconds all of the lights except the power light will go out.

How do I setup my Grandstream HT502?

Connect the RJ-11 telephone cable connected to your telephone into Phone 1 port on the HT502.

  1. Reconnect the plug into your cable or DSL modem and wait until the lights stabilize on that device.
  2. Connect the included power adapter to the HT502 power port and plug the power adapter into an electrical outlet in the wall.

How do I set up my Grandstream ATA?

Installing Grandstream HT801 ATA Devices

  1. Capture the device’s IP Address. Plug in an analog handset into the phone jack, go off-hook, listen for dial tone and dial “***” (three * tones).
  2. Reset the HT801 ATA to factory default.
  3. Configure the Grandstream HT801 ATA.
  4. Click the Advanced Settings menu.

What is grandstream HT502?

Grandstream HandyTone 502 – HT502. The Grandstream HandyTone 502 is a two-line analogue telephone adapter with a built-in single port wired 10/100Mbps LAN router and network address translation (NAT). It is reported to support both tone and pulse dial (a capability which was removed from the later HT702).

How do I factory reset my Grandstream ATA?

Factory Reset the Device

  1. Plug in and power on the ATA device.
  2. Locate the indented RESET button between the power and ethernet port.
  3. Use a paper clip or toothpick to press and hold the reset button for 10 seconds. Do not release the button until all 4 lights on the top of the ATA flash for 1-2 seconds.

How do I reset my Grandstream ATA?

How do I reset my Grandstream admin password?

Page 142 of admin guide:

  1. Power cycle the phone.
  2. Wait till you see “booting”.
  3. When phone is “booting”, press KEY 1 + Key 9 immediately and hold it until LCD factory reset. message or if a password is required.
  4. If it is required, enter the correct admin password to factory reset.
  5. Factory reset is complete.

How do I Factory Reset my Grandstream GXP2140?

Factory Reset Grandstream GXP2140/GXP2160

  1. Press the menu button (center button of the directional pad).
  2. Use the directional pad to select ‘System’.
  3. Use the directional pad to select ‘Factory Reset’.
  4. Press ‘YES’ to confirm factory reset.
  5. Your phone will reboot.

How to configure the Grandstream ht502 with a static IP address?

How to configure the Grandstream HT502 with a Static IP Address. IP address: 192.168.1.200 Subnet Mask: 255.255.255.0 Default Router: 192.168.1.1 DNS Server1: 208.67.222.222 DNS Server2: 208.67.220.220 Scroll to the bottom of the window and click Update . On the next screen click Reboot . Your Grandstream will now always use…

What is the Grandstream handytone 502?

The Grandstream HandyTone 502 is a two-line analogue telephone adapter with a built-in single port wired 10/100Mbps LAN router and network address translation (NAT). It is reported to support both tone and pulse dial (a capability which was removed from the later HT702 ).

How do I access the ht502 configuration page?

The HT502 HTML configuration page can be accessed via LAN or WAN ports. •FROM THE LANPORT: 1. Directly connect a computer to the LAN port 2. Open a command window on the computer 3.

What are the features of ht502?

The HT502 is a full feature voice and fax-over IP device that offers a high-level of integration including dual 10M/100Mbps network ports with integrated router, NAT, DHCP server, dual port FXS telephone gateway, market-leading sound quality, rich functionalities, and a compact and lightweight design.